How to Do Your Own Water Heater Maintenance

Installing a water heater is easy, but it requires a little bit of attention to detail. There are various things that you need to check in the event of a malfunction, so that you can prevent further issues. You may think that these suggestions are too much work, but it will be worth it in the end. Below, we will discuss some of the most essential things that you need to check before hopping into your car and driving off to work.

Make Sure The Unit is Covered By Service

This one seems obvious, but many people fail to do it. When you buy a new water heater, make sure that it is protected by service. Many companies offer limited parts and labor warranties, so it is essential to make sure that your warranty is not affected. You must have the original receipt from the dealer or service provider in order to make a claim under the warranty. In the event of a malfunction, the warranty can become void if you have not had the unit serviced within the first year.

Check For Leaks

Many water heaters have an element positioned near the hot water spout. These elements are made of a thin metal, and you must ensure that they are not leaking. If they are leaking, it indicates that there is likely to be a hot water leak somewhere in the system. It is essential that you fix this problem before it gets any worse, so make sure that you conduct a thorough inspection of the entire unit, looking for any leaks. You should test for excessive dripping in the near future, so that you can determine the exact location of the leak. In the event of a serious leak, you may have to replace the entire element. This is a costly repair, but it is essential to protect your home from water damage.

Clean It Regularly

Just like any other surface that comes into contact with water, your water heater can become clogged with particles over time. This will affect the efficiency of the unit, as well as cause serious damage to your plumbing. To avoid this, you must clean it at least once every month. The easiest way to do this is by blasting it with a water hose. Make sure to rinse it well after each cleaning session. In the event that the particles inside are not removable with cleaning products, it may be necessary to replace the entire unit.

Test It Often

In the same way that you would test the efficiency of an air purifier or HEPA vacuum cleaner, you must test the pressure of your water supply regularly. To do this, simply turn on the water and leave it for a few hours. When you return, check to see if there is any puddles of water on the floor. This is a sign that the tank is losing pressure, and it must be fixed immediately. In the event of a serious leak, it may be necessary to replace the entire unit. Make sure to test for leaks in the near future so that you can determine the exact location of the leak and fix it promptly.

Look For Nail Holes

One of the most common issues that people face is the slow leak that develops from a nail hole in the tank. In the event that there are no signs of forced entry, it may be a result of corrosion that has slowly eaten away at the tank. To combat this, you must keep track of any previous leaks, as this will help you determine the cause of the recent one. As mentioned above, you must also clean your water tank every month, and this is where nail holes develop as a result of constant scrubbing with a wire brush. You can prevent this by painting the inside of the tank with a water-resistant paint. This will prevent leaks and keep the water clean. Corrosion is also a major issue in the event of a toilet leak. Toilet valves can be damaged by constant exposure to water, and it is essential that you fix these issues before they get worse. There are various things that you can do to prevent these kinds of damages, such as keeping your toilet bowl dry by using a tissue or installing a water-saving shower head.

Know How To Regulate The Temperature

Whether you like it or not, your water heater will eventually get to a point where it is too hot or too cold. To avoid this, you must learn how to regulate the temperature. This can be done using a thermostat, which will stop the flow of water when the temperature is outside of a certain range. In the event that you use an adjustable thermostat, it will increase or decrease the temperature as you approach or move away from the optimal operating range, respectively. As a general rule of thumb, if you live in a cold climate, you should set the temperature as low as reasonably possible, and if you live in a warmer climate, you should set it at a level that is comfortable for you.

Check For Stale Gas

If you use gas for cooking or heating, then you must be sure to check for any signs of staleness. You can do this by smelling it whenever you use a burner. In the event of a large leak, it may be necessary to replace the entire unit as soon as possible. Make sure to test for leaks regularly so that you can locate the source of the problem and fix it promptly.

Look For Signs Of Trouble

Even if you take all of the precautions listed above, you may still face issues that are ultimately beyond your control. As a result of aging or mineral deposits in the tank, it may become necessary to replace the entire unit at some point. To do this, you must first determine the location of the trouble by studying the operation of the water heater continuously, looking for patterns of behavior that may signal a malfunction. When you have pinpointed the area of concern, you can then move on to either replace the entire unit or fix it with the help of a professional plumber.

Installing a water heater is easy, but it requires a little bit of attention to detail. There are various things that you need to check in the event of a malfunction, so that you can prevent further issues. You may think that these suggestions are too much work, but it will be worth it in the end. Below, we will discuss some of the most essential things that you need to check before hopping into your car and driving off to work.

Make Sure The Unit is Covered By Service

This one seems obvious, but many people fail to do it. When you buy a new water heater, make sure that it is protected by service. Many companies offer limited parts and labor warranties, so it is essential to make sure that your warranty is not affected. You must have the original receipt from the dealer or service provider in order to make a claim under the warranty. In the event of a malfunction, the warranty can become void if you have not had the unit serviced within the first year.

Check For Leaks

Many water heaters have an element positioned near the hot water spout. These elements are made of a thin metal, and you must ensure that they are not leaking. If they are leaking, it indicates that there is likely to be a hot water leak somewhere in the system. It is essential that you fix this problem before it gets any worse, so make sure that you conduct a thorough inspection of the entire unit, looking for any leaks. You should test for excessive dripping in the near future, so that you can determine the exact location of the leak. In the event of a serious leak, you may have to replace the entire element. This is a costly repair, but it is essential to protect your home from water damage.

Clean It Regularly

Just like any other surface that comes into contact with water, your water heater can become clogged with particles over time. This will affect the efficiency of the unit, as well as cause serious damage to your plumbing. To avoid this, you must clean it at least once every month. The easiest way to do this is by blasting it with a water hose. Make sure to rinse it well after each cleaning session. In the event of a serious leak, it may be necessary to replace the entire unit.

Test It Often

In the same way that you would test the efficiency of an air purifier or HEPA vacuum cleaner, you must test the pressure of your water supply regularly. To do this, simply turn on the water and leave it for a few hours. When you return, check to see if there is any puddles of water on the floor. This is a sign that the tank is losing pressure, and it must be fixed immediately. In the event of a serious leak, it may be necessary to replace the entire unit. Make sure to test for leaks in the near future so that you can determine the exact location of the leak and fix it promptly.

Rate a page
Add a comment